This application will allow us full control in Alarm Systems Company Tecnordeste. We can activate and deactivate the alarm from anywhere via the Internet. Also we receive notifications of the Current Status of the alarm and when it is triggered.
On the Home screen we have 3 tabs, the main "STATUS" tab indicates the current status of the alarm, below has a sliding button to turn on or off depending on the state in which we find ourselves.
The "ACTION" tab provides different buttons for different modes of activation,
_ Common Activation: It is the most common activation system, which performs triggering the alarm when motion is detected. In the Cell notifying the application will run this event.
_ Activation Pre-Trip Time: Designed for use when we are in our home, motion detection run on our mobile A countdown clock where we can turn off the alarm, if not to do is execute the shot her and alerted us to our mobile as in the previous case.
_ Silent Alarm Activation: This system is a silent alarm which does not run the siren when it detects movement, but warns us in the cell like that has befallen the shot.
Finally the "History" tab shows all the actions we have taken indicating date and time of each.
Application works through Internet, and data consumption is minimal, working perfectly both wireless and cellular networks (2G, 3G, and 4G). In the event that the Internet connection is defective at the time of alarm trip, we will receive a notice when the connection is restored.
To link your mobile device with alarm, we check in and we will provide a username and password, these are free and will operate indefinitely. Then we pass this data to the alarm, the alarm for this will be detected automatically by the application and we ask the WiFi network we want to connect our alarm.
If we want to control the alarm from several mobile devices only have to enter the same username and password for all devices you want to use.
If the Internet connection were to address problems Alarm re-attempt to connect indefinitely and also work, but the message to the mobile device may not be carried out. When the connection is restored the alarm automatically send a warning that has been fired.
When we are at our home and want to disable or enable (if the Internet connection has not yet been restored) our mobile device tries to connect directly to the alarm to send off signal without Internet (a direct link is made by wireless between Cellular and Alarm).
We can set the alarm completely through the Application, both to modify the tripping time, as the Pre-Trigger time, the trip time of Unfriendly button, the activation and deactivation Notices, Etc.
We may also set the volume and sound for notifications that come to our Cell in status changes in the warning shot, and in the Notice countdown.
For any questions or to purchase any of our alarm can be directed to the following email:
emilioarengo@gmail.com
On the Home screen we have 3 tabs, the main "STATUS" tab indicates the current status of the alarm, below has a sliding button to turn on or off depending on the state in which we find ourselves.
The "ACTION" tab provides different buttons for different modes of activation,
_ Common Activation: It is the most common activation system, which performs triggering the alarm when motion is detected. In the Cell notifying the application will run this event.
_ Activation Pre-Trip Time: Designed for use when we are in our home, motion detection run on our mobile A countdown clock where we can turn off the alarm, if not to do is execute the shot her and alerted us to our mobile as in the previous case.
_ Silent Alarm Activation: This system is a silent alarm which does not run the siren when it detects movement, but warns us in the cell like that has befallen the shot.
Finally the "History" tab shows all the actions we have taken indicating date and time of each.
Application works through Internet, and data consumption is minimal, working perfectly both wireless and cellular networks (2G, 3G, and 4G). In the event that the Internet connection is defective at the time of alarm trip, we will receive a notice when the connection is restored.
To link your mobile device with alarm, we check in and we will provide a username and password, these are free and will operate indefinitely. Then we pass this data to the alarm, the alarm for this will be detected automatically by the application and we ask the WiFi network we want to connect our alarm.
If we want to control the alarm from several mobile devices only have to enter the same username and password for all devices you want to use.
If the Internet connection were to address problems Alarm re-attempt to connect indefinitely and also work, but the message to the mobile device may not be carried out. When the connection is restored the alarm automatically send a warning that has been fired.
When we are at our home and want to disable or enable (if the Internet connection has not yet been restored) our mobile device tries to connect directly to the alarm to send off signal without Internet (a direct link is made by wireless between Cellular and Alarm).
We can set the alarm completely through the Application, both to modify the tripping time, as the Pre-Trigger time, the trip time of Unfriendly button, the activation and deactivation Notices, Etc.
We may also set the volume and sound for notifications that come to our Cell in status changes in the warning shot, and in the Notice countdown.
For any questions or to purchase any of our alarm can be directed to the following email:
emilioarengo@gmail.com
Show More
